Warehouse floor repairs in London are usually about time. Buildings are expensive to leave idle, fit-outs run to tight programmes and operations rarely stop. Contact Flooring repairs damaged concrete and failed resin floors for warehouses, refurbishment projects, industrial units and commercial buildings across London and the South East, and we plan the work around the hours you can give us.
Industrial floor repairs in London: older buildings, mixed substrates
London's industrial floors range from modern logistics sheds around Park Royal, Enfield, Dagenham and the Heathrow corridor to much older buildings that have been converted and refurbished several times. In older buildings especially, what sits under the surface can be a surprise: thin screeds, previous repairs and even original timber floors. A repair or new finish only lasts if the substrate is understood first.
Typical defects we repair include:
- self-levelling and resin systems that have failed because of poor priming or preparation;
- cracks, spalling and holes in concrete slabs;
- broken joints and arrises in forklift and pallet truck routes;
- uneven areas and level differences at doors and thresholds.
Case study: 322m2 flexible self-smoothing floor, London
Working for a well-regarded London refurbishment company, our brief was purely time-driven: a polyurethane self-levelling system had been installed incorrectly and was failing after just one week. Our investigation showed the priming had not been carried out properly and the substrate had not been dealt with.
We agreed five days to put it right. The 3mm polyurethane was removed by machine where it was bonded and with tile lifters where it had failed. Underneath was a thin screed, well bonded in most places, but where it had failed there was an old wood block floor forming the main structure. After preparation and repairs, the ground floor and basement were flooded with a water based primer to seal every cavity, followed by two coats of polyurethane primer and a 3mm polyurethane flexible self smoothing system, giving a high gloss, very smooth finish. Read the London case study.
Case study: weekend warehouse floor repair, Oxford
For an international car parts manufacturer in Oxford, an urgent repair was needed to meet a health and safety requirement. The work was done over a weekend with an epoxy based repair mortar. The damage was ground out until the middle of the area was almost 40mm deep, then filled with a scratch coat heavily loaded with silica sand and finished with a high build coating. Read the Oxford case study.
The same approach suits many London warehouses: isolate the area, repair it out of hours, and hand it back for the next shift.
Planning repairs around a London site
Access, parking, loading bay slots and building management rules often shape a London job as much as the floor itself. At survey we agree:
- which areas can be released, and for how long;
- working hours, including nights and weekends where needed;
- dust control, with extraction on preparation machines;
- when each area will be ready for foot and vehicle traffic.
Our team travels to London sites from our offices, and we plan each visit so that the time on site is used well.
Refurbishments and change of use
When a London building is being refurbished or taken over by a new occupier, the floor is best dealt with before fit-out, while the space is empty. Removing failed finishes, repairing the substrate and installing a new system later, around racking, plant and people, is far more disruptive.
Repair or start again?
If the slab is sound and damage is local, targeted repairs are the quickest fix. If a previous system has failed across the floor, as in the London 322m2 project, removal, substrate repairs and a new system is the reliable route. The concrete floor repairs and renovation page explains the options, and the main warehouse floor repairs page covers the methods. For new installations, see our resin flooring contractors in London page.
Common questions
Why has our new resin floor failed so quickly?
Early failure is very often down to preparation or priming. In the London 322m2 project, a self-levelling system failed after a week because priming had not been completed and the substrate had not been dealt with.
Can you work nights or weekends in London?
Yes. The Oxford repair was completed over a weekend, and out-of-hours working can be agreed at survey.
Can resin go over an old timber or block floor?
It depends on what is there and how sound it is. That is why we investigate the substrate before specifying any repair or finish.
Arrange a London survey
Call 0161 726 5095 or request a quote to book a site survey.