Contact Flooring carries out warehouse floor repairs in Glasgow and the west of Scotland, for warehouses, workshops, manufacturing units and vehicle facilities. One of our largest repair-and-resurface projects was a 2215m2 car body repair centre just outside Glasgow, where years of surface damage and old coatings had to be dealt with on a strict budget. If your floor is damaged and you need a practical, cost-conscious fix, that project is a good guide to how we work.
Industrial floor repairs in Glasgow: repair and resurface on a budget
Many Glasgow sites have floors that have been coated, patched and re-coated over the years by different contractors. The result is a surface with old coatings of varying thickness, damage from previous work and undulations in the concrete. Two easy answers exist, a thick self-levelling system or a pumped screed, but neither always fits the budget.
The alternative is to remove what is failing, repair the substrate, then build up a thinner system designed to take out the remaining imperfections. Done properly, this gives a flat, functional floor without the cost of a full new screed.
Case study: car repair centre near Glasgow, 2215m2
This client, a highly regarded car body shop repair specialist located just outside Glasgow, wanted a flat, functional floor whose appearance matched the high quality finishes in the rest of the building, within a strict budget.
The challenges were:
- existing epoxy coatings of various thicknesses in different parts of the building, which had to be removed;
- lots of surface damage left by the previous company;
- a chosen system that would finish at between 1.5mm and 2mm, so the damage and undulations had to be addressed before it went down.
We agreed with the client that a hard-wearing epoxy system with a two coat UV stable finish was the right specification. To create some thickness and help eliminate the damage and undulations, an epoxy scratch coat was applied by squeegee and back rolled at approximately 1mm. Two coats of UV stable, chemical resistant coating followed, in mid grey and light grey to separate traffic lanes from parking bays, and parking bays and door entrances were finished with 100mm demarcation lines. Read the car repair centre case study.
Areas we cover around Glasgow
We work across Glasgow and the west of Scotland, including Hillington, Govan, Cambuslang, Clydebank, Paisley, Motherwell and Eurocentral. Our team travels to Scottish sites, so we plan each job to make the most of every visit, grouping repairs so the work is completed in as few mobilisations as possible.
Damage typical of workshops and vehicle facilities
- Oil, fuel and fluids soaked into the concrete, which must be dealt with in preparation.
- Impact damage from dropped tools and parts.
- Broken joints and worn surfaces where vehicles turn.
- Old inspection pits and level differences at doors.
- Peeling coatings laid over poorly prepared concrete.
The same methods apply in Glasgow warehouses and distribution units: crack injection, repair mortars, cut and patch, and flexible resin joint repairs. Full details are on our main warehouse floor repairs page.
Budget-led does not mean cutting corners on preparation. On the car repair centre, removing the old coatings and dealing with the damage underneath was what made a thinner system work.
Choosing between repair and a new floor
If damage is limited, a targeted repair is the quickest answer. Where the whole floor is tired, uneven or carrying failed coatings, the repair-and-resurface approach used at the car repair centre often gives the best balance of cost and performance. Our concrete floor repairs and renovation page sets out the options. For new resin systems, see our resin flooring contractors in Glasgow page, and for the east of Scotland see our Edinburgh floor repairs page.
Common questions
Can you repair our floor without the cost of a full new screed?
Often, yes. Removing failed coatings, repairing the substrate and applying a scratch coat before the finish can take out damage and undulations at a lower cost than a thick system.
Can old epoxy coatings of different thicknesses be removed?
Yes. This was part of the 2215m2 car repair centre project. Mechanical preparation removes the old coatings so repairs can be made to the concrete.
Can you mark out traffic lanes and parking bays after repairs?
Yes. Different colours and 100mm demarcation lines were used on the car repair centre to separate traffic lanes from parking bays.
Arrange a survey in Glasgow
Call 0161 726 5095 or request a quote to arrange a site survey.